The University of Kitakyushu Murakami Laboratory

  • The University of Kitakyushu
  • Faculty of Environmental Engineering

Achievement　研究業績　2010〜

Journal papers　学術雑誌投稿論文

Hiroshi MURAKAMI，Akio KATSUKI, Hiromichi ONIKURA，Takao SAJIMA, Norio KAWAGOISHI, Eiji KONDO：An Optical Fiber Probe for 3-D Micro Metrology，Key Engineering Materials, Vols. 447-448（2010），pp.524〜528.

村上 洋，甲木 昭雄，鬼鞍 宏猷，佐島 隆生，皮籠石紀雄，近藤英二：光ファイバプローブを用いた微小径穴形状精度測定システムの開発（第2報）−試作した測定システムの評価実験−，精密工学会誌，76巻・8号（2010），pp.950〜954 .

Hiroshi MURAKAMI，Akio KATSUKI, Hiromichi ONIKURA，Takao SAJIMA, Norio KAWAGOISHI, Eiji KONDO, Development of a System for Measuring Micro Hole Accuracy Using an Optical Fiber Probe, Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol.4, No.5(2010), pp.995〜1004.

Hiroshi Murakami，Norio Kawagoishi, Eiji Kondo，Akira Kodama：Optical Technique to Measure Five-Degree-of-Freedom Error Motions for a High-Speed Microspindle, International Journal of Precision Engineering and Manufacturing, Vol.11, No.6 (2010), pp.845〜850.

Akio KATSUKI, Hiromichi ONIKURA, Takao SAJIMA, Akira MOHRI, Tomoyuki MORIYAMA, Yutaka HAMANO, Hiroshi MURAKAMI, Developmenet of a practical high-performance laser-guided deep-hole boring tool, Precision Engineering, Vol.35 (2011), pp.221〜227.

甲木 昭雄，鬼鞍 宏猷，佐島 隆生，村上 洋，佐藤 剛，Thomas CAETANO，MD.Hazrat ALI，大西 修：深穴の高速オンマシン形状精度測定に関する研究，精密工学会誌，77巻・7号（2011），pp.681〜687.

甲木 昭雄，鬼鞍 宏猷，佐島 隆生，村上 洋，土肥俊郎，佐藤 剛，西裕徳，Valentine Pietri，MD.Hazrat ALI：レーザ誘導方式深穴評価システムの開発，精密工学会誌，77巻・10号（2011），pp.977〜984.

Takao SAJIMA, Hiroshi MURAKAMI, Akio KATSUKI, Daisuke TABUCHI, Osamu OHNISHI, Syuhei KUROKAWA, Hiromichi ONIKURA, Toshiro K. Doi, Precision Profile Measurement System for Micro Holes Using Vibration Optical Fiber, Sensors and Materials, Vol.24, No.7 (2012), pp.387-396.

Eiji KONDO, Ryoga KAMO, Hiroshi MURAKAMI, Monitoring of Burr and Prefailure Phase Caused by Tool Wear in Micro-Drilling Operations Using Thrust Force Signals, Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol.6, No.6 (2012), pp.885〜897.

Hiroshi MURAKAMI, Akio KATSUKI, Takao SAJIMA, Analysis and Evaluation of Surface Force Effects in Vibrating Fiber Probing System for 3-D Micro Structure Measurements, Key Engineering Materials, Vol.523-524 (2012), pp.907-912.

MD. Hazrat ALI, Akio KATSUKI, Takao SAJIMA, Hiroshi MURAKAMI, Syuhei Kurokawa, Control Strategy of Developed Mechanical Actuator in Measuring Hole-Surface Parameter, International Journal of Advanced Manufacturing Technology, Vol.69, No.5-8 (2013).

Hiroshi MURAKAMI, Akio KATSUKI, Takao SAJIMA, Simple and simultaneous measurement of five-degrees-of-freedom error motions of high-speed microspindle: Error analysis, Precision Engineering, Vol.38 (2014), pp.249-256.

Hiroshi MURAKAMI, Akio KATSUKI, Takao SAJIMA, Takuya SUEMATSU, Study of a vibrating fiber probing system for 3-D micro-structures: performance improvement, Measurement Science and Technology, 25 (2014) 094010.

Murakami H, Katsuki A, Sajima T. Development of Touch Probing System Using a Fiber Stylus. Fibers. 2016;4:13.

Murakami H, Katsuki A, Sajima T, Fukuda M. Reduction of Liquid Bridge Force for 3D Microstructure Measurements. Appl Sci-Basel. 2016;6:11.

Ali MH, Katsuki A, Sajima T, Murakami H, Kurokawa S. Control strategy of developed mechanical actuator in measuring hole surface parameter. Int J Adv Manuf Technol. 2016;84:777-86.

Murakami H, Katsuki A, Sajima T, Uchiyama K. Fabrication of Ultra-Small-Diameter Optical-Fiber Probe Using Acid-Etch Technique and CO2 Laser for 3D-Micro Metrology. International Journal of Automation Technology. 2017;11:699-706.

Katsuki A, Sajima T, Murakami H, Hazrat AM, Ohnishi O, Akashi K. Development of a laser-guiding-type deep small-sized hole-measurement system: Measurement accuracy. Precision Engineering. 2020;63:18-32.
https://doi.org/10.1016/j.precisioneng.2019.12.012

Hiroshi Murakami, Akio Katsuki, Takao Sajima, Kosuke Uchiyama, Ichiro Yoshida, Yasuo Hamano, Hiroshi Honda, Development of measurement system for microstructures using an optical fiber probe: improvement of measurable region and depth, Measurement Science and Technology, 2020
https://doi.org/10.1088/1361-6501/ab7efc

Hiroshi Murakami, Akio Katsuki, Takao Sajima, Kosuke Uchiyama, Ichiro Yoshida, Yasuo Hamano, Hiroshi Honda, Investigation of Factors Affecting Sensitivity Enhancement of an Optical Fiber Probe for Microstructure Measurement Using Oblique Incident Light, applied sciences, 10, 3191, 2020
https://doi.org/10.3390/app10093191

Hiroshi Murakami, Akio Katsuki, Takao Sajima, Kosuke Uchiyama, Keisuke Houda, Yuta Sugihara. Spindle with built-in acoustic emission sensor to realize contact detection. Precision Engineering. 2021;70:26-33.
https://doi.org/10.1016/j.precisioneng.2021.01.017

Kosuke Uchiyama, Hiroshi Murakami, Akio Katsuki, Takao Sajima. Development of a Sharp-Tipped L-Shaped Stylus for Measurement of Nanoscale Sidewall Features. International Journal of Automation Technology. Vol. 16, No.4, pp.489-496, 2022.
https://doi.org/10.20965/ijat.2022.p0489

 

村上洋. 微細形状測定機用マイクロファイバスタイラスの製作技術. 精密工学会誌. Vol. 88, No.9, pp.678-683, 2022.  

Hiroshi Murakami, Hiroki Murakami, Akio Katsuki, Takao Sajima, Kosuke Uchiyama, . Development of a two-step stylus with elastic hinge for microstructure measurement to improve sensitivity and vibration characteristics. Precision Engineering. Vol. 80, pp.72-81, 2023.
https://doi.org/10.1016/j.precisioneng.2022.11.015

Hiroshi Murakami, Kosuke Uchiyama, Akio Katsuki, Takao Sajima, Kunitaka Fujiyoshi. Development of a High-Function Fiber Stylus for Microstructure Measurement with Water-Repellent and Antistatic Coatings. Applied Sciences. Vol. 13, No.3, 1260, 2023.
https://doi.org/10.3390/app13031260


PAGETOP